There will be a New Member Orientation on Saturday, July 30, 2022 beginning at 09:00 in the reefer conference area at the locomotive restoration site located at 1833,  8th street in the reefer conference area. This orientation will last most of Saturday so be prepared to spend all day on site. (we will have a lunch […]

Announcements

July 12, 2022

New Member Orientation

January 27, 2022 I haven’t sent out a TW3 for a while mostly because we have been doing, for the most part, the same jobs every session. That being said it has been insulation, jacketing and electrical systems, and tool car work. Much attention has been focused on the Positive Train Control (PTC) system. Since […]

TW3

January 27, 2022

TW3 (That Was the Week That Was)

August 02, 2021 By now I suppose everyone is aware of our steam-up and the roll of 2926 on 7/24-25/2021. The 2926 rolled proudly up and down our short spur track to the delight of all those able to attend. We could have done this several months ago, but I made it known I wouldn’t […]

CMO Report

August 2, 2021

CMO Status Report

June 12, 2021 Welcome everyone to the first General Membership meeting in more than 15 months. For those of you who haven’t been here we have been doing small projects; electrical installations, tool car jobs including 480 pass-through brackets, interior painting, generator installation equipment and also fabricating new doors. Our AMTRAK inspector was here last […]

CMO Report

June 12, 2021

CMO Status Report

December 21, 2020 Hello all, This will most likely be my last TW3 for this on again off again 2020 year. Our state mandates have played havoc with our restoration. Nevertheless, we have complied as necessary and persevered where we were able. Much of the 2926 work prior to May, when the tool car arrived, […]

TW3

December 21, 2020

Work Session Status Week Ending 12/19/2020

November 10, 2020 Hello everyone, It’s been awhile since I wrote a progress report since most of the work has been the same for quite some time. Many hours have been spent on the interior of the tool car wire brushing all the sides ends and ceiling in preparation for the painting. We hired an […]

TW3

November 10, 2020

Work Session Status Week Ending 11/07/2020

August 18, 2020 Hello all, This is our first TW3 since this past March. As most of you know, the tool car arrived on site 5/5/2020. Since then we have been back to work on a limited basis. We have been working to remove the included donated items from the car. The first project for […]

TW3

August 18, 2020

Work Session Status Week Ending 08/15/2020

May 28, 2020 The New Mexico Steam Locomotive and Railroad Historical Society extends wishes for good health and safety to all of our NMSL&RHS friends during this adjustment to the new normal for dedicated Ferroequinologists. The AT&SF 2926 has been resting comfortably in her engine house for the last couple of months, while her support […]

TW3

May 28, 2020

TW3 Update

May 6, 2020 Greetings steamers, I wanted to reach out to all of our members and support network. I hope all are well and have not been afflicted by this ornery virus. As of yesterday, at 12:00 p.m. and after approximately two and a half years of truck repair work, $10,000+ in transit costs from […]

TW3

May 6, 2020

Work Session Info

March 16, 2020 Due to the State of New Mexico’s mandate to limit public places either closed or capacities of 50% of their normal persons, the Saturday 3/21/2020 steam-up we planned to have open to the public has been cancelled, however visitors are still welcome to see the normal work day. Our Friday 3/20/2020 members […]

TW3

March 16, 2020

TW3 Abbreviated Special Announcement

Follow us